Browsing by Author "Kovalchuk, Yuri"
Now showing 1 - 3 of 3
Results Per Page
Sort Options
Item Estimation of Carrying Capacity of Metallic Corrugated Structures of the Type Multiplate MP 150 During Interaction with Backfill Soil(PC "Technology Center", Ukrainian State University of Railway Transport, Kharkov, 2018) Kovalchuk, Vitalii V.; Kovalchuk, Yuri; Sysyn, Mykola P.; Stankevych, Volodymyr Z.; Petrenko, Oleksiy V.EN: We estimated the stressed state of a railroad structure with a large cross section spanning more than 6 m, which is made from metallic corrugated sheets of the type Multiplate MP 150. The stressed-strained state of the corrugated structure was estimated depending on the residual deformation of vertical diameter of the pipe, the modulus of elasticity of backfill soil, and the degree of compaction. The study conducted has demonstrated that maximum stresses occur on the horizontal sides of a metallic pipe, and maximum deformations ‒ in the pipe vault. It was established that an increase in the degree of compaction of backfill soil leads to a decrease in the stresses in a metallic pipe by almost half. The stresses grow much faster with an increase in irregularity on the railroad track. Numerical calculations have shown that the equivalent stresses exceed the permissible magnitude of 235 MPa when the degree of compaction of backfill soil is below 90 % and an operational irregularity on the track develops beyond the permissible magnitude. Operational observations have shown that the pipe is most vulnerable, in terms of resistance against the formation of a plastic hinge, in the initial period of operation when the backfill soil has not yet reached the standard compaction. At the initial stage of operation of a metallic corrugated pipe it is necessary to improve the level of technological control in order to timely detect railroad track's irregularities that exceed the standards, and to eliminate them. Under normal operational conditions, a metallic corrugated structure has a rather large reserve of carrying capacity, which amounts to 80 %. However, these structures, despite their high initial strength margin, are very sensitive to an increase in external dynamic loads due to the occurrence of irregularity on the railroad track.Item Experimental Study of Railway Trackred Pressure Distribution under Dynamic Loading(Riga Technical University, Latvia, 2019) Sysyn, Mykola P.; Kovalchuk, Vitalii V.; Nabochenko, Olga S.; Kovalchuk, Yuri; Voznyak, Oleg M.EN: Abstract. Reliable and durable operation of the railway track under the dynamic load of the rolling stock depends considerably on the ability of the ballast layer to get the load from the sleepers and distribute it to the subgrade. In this paper, the experimental study of the distribution properties of the ballast layer under the impact of dynamic loading depending on the density of the ballast layer is carried out. The ballast behaviour during load cycles is estimated by pressure measurements at the ballast prism base along the axis of a sleeper with simultaneous video observation of the ballast particles movement through transparent sidewalls of the box with crushed stone. Measurements of pressure distribution are carried out with the developed microcontroller system of measurements and developed load cells. The system allows performing multi-point measurements of stress in combination with measurements of acceleration and photogrammetry. The results of measurements showed a significant effect of the ballast layer consolidation on the distribution of stresses under the sleeper. The performed research opens up opportunities for practical improvement of the existing types of track structures and the technology of the ballast layer tamping in terms to provide the optimal conditions for the ballast layer operation.Item Studying the Railroad Track Geometry Deterioration as a Result of an Uneven Subsidence of the Ballast Layer(НВП ПП «Технологічний Центр», Харьків, 2019) Nabochenko, Olga S.; Sysyn, Mykola P.; Kovalchuk, Vitalii V.; Kovalchuk, Yuri; Pentsak, Andrii Ya.; Braichenko, S.EN: A method for calculating impairment of the track geometry under influence of dynamic loads in the course of passing the track unevenness by the rolling stock was developed. The method takes into consideration interrelated short-term processes of dynamic interaction and long-term processes of subsidence of the ballast layer in a mutual influence on each other. Mathematical model of dynamic interaction of the track in the form of a planar three-layer continual beam system with a two-mass discrete system corresponding to the rolling stock is the basis of the first part of the method. This model makes it possible to simulate dynamic loads from individual sleepers to the ballast when the rolling stock passes geometric unevennesses and the track elasticity unevennesses.The second part of the method is based on the phenomenological mathematical model of accumulation of residual deformations formed using the results of laboratory studies of subsidence of individual sleepers in the ballast layer. Peculiarity of this model consists in taking into consideration not only uniform accumulation of residual subsidence from the passed tonnage but also presence of a plastic component of subsidence which depends on the maximum stresses in the history of ballast loading by each sleeper. A new theoretical mechanism of development of the track unevenness was proposed. It takes into consideration not only residual subsidences of the ballast layer but also appearance of gaps under sleepers resulting in a local change of the track elasticity. This mechanism enables taking into consideration the ambiguous influence of subsidences with occurrence of gaps under the sleepers. Subsidence causes an increase in dynamic loads on the track and the ballast layer on the one hand and onset of the gap causes a decrease in the track rigidity and corresponding reduction of dynamic loads on the other hand. Practical application of the developed method was demonstrated on an example of quantitative estimation of long-term uneven subsidences of the ballast layer when changing the sleeper diagram.